Category Archives: InfoWorks CS

Storage Nodes

There have been several questions raised recently with regard to storage nodes and how these react to levels that exceed the defined storage array. The relationship between the storage parameters tab of the storage node and the ground level will … Continue reading

Posted in InfoWorks CS, InfoWorks ICM | Comments Off on Storage Nodes

Groundwater Infiltration Module in Infoworks ICM (and legacy CS)

Introduction The purpose of this blog is to provide a guide to the groundwater infiltration module (GIM) within Infoworks ICM and legacy Infoworks CS. The blog will begin by describing why the GIM is important and focuses on the limitations … Continue reading

Posted in InfoWorks CS, InfoWorks ICM | Tagged , , , , , , , | Comments Off on Groundwater Infiltration Module in Infoworks ICM (and legacy CS)

Catchment Tree Structure from CS into ICM

Within InfoWorks CS it is possible to create new networks from an existing state via either a check-out or a check-out and branch. A check-out and branch is designed to allow multiple scenarios from a singular base to be tested, … Continue reading

Posted in InfoWorks CS, InfoWorks ICM | Tagged , , , , , , , | Comments Off on Catchment Tree Structure from CS into ICM

Exciting news for ICM Modellers and InfoNet Asset Managers in the UK.

The Environment Agency has recently announced that Light Detection and Ranging (LiDAR) data will be made available for free for the first time as part of the Open Data strategy. The Environment Agency has been collecting LiDAR data for the … Continue reading

Posted in H2OMAP Sewer, InfoNet, InfoWorks CS, InfoWorks ICM, InfoWorks RS, InfoWorks SD | Tagged , , , , | Comments Off on Exciting news for ICM Modellers and InfoNet Asset Managers in the UK.

Don’t forget your 2D Initial Conditions!

A couple of recent 2D models have been seen where a tidal boundary is being represented and results on the 2D mesh show water surface elevations greater than the tidal level…this is due to poor model schematisation and in particular the … Continue reading

Posted in InfoWorks CS, InfoWorks ICM, InfoWorks RS, InfoWorks SD | Tagged , , , , , | Comments Off on Don’t forget your 2D Initial Conditions!

Transferring CS to ICM

Transferring data from CS to ICM is a very simple and straight forward procedure. To transfer your data from IWCS to ICM you need to start the CS administrator and then open InfoWorks explorer via the “View” menu    Then … Continue reading

Posted in InfoWorks CS, InfoWorks ICM | Comments Off on Transferring CS to ICM

Fixed and Floating licences for InfoWorks ICM

Many people believe that InfoWorks ICM can only be configured to run as a Workgroup product if you authenticate by a Network Dongle or Floating Soft Licence.  This is not the case; the choice of authentication (Local Dongle, Network Dongle, … Continue reading

Posted in Information Technology, InfoWorks CS, InfoWorks ICM | Tagged , | Comments Off on Fixed and Floating licences for InfoWorks ICM

InfoWorks Simulations (32-bit vs. 64-bit)

InfoWorks CS is a pure 32-bit application. InfoWorks ICM is available in both 32-bit and 64-bit editions. It’s a very common misconception that 64-bit applications are a lot faster than 32-bit ones.  That is not the case in general, and … Continue reading

Posted in InfoWorks CS, InfoWorks ICM | Tagged , | Comments Off on InfoWorks Simulations (32-bit vs. 64-bit)

The Next Frontier: Representing Groundwater Interactions in InfoWorks ICM – User Case Study

A case study has been written by one of our clients that shows how their modellers have used InfoWorks ICM functionality to represent the interaction of groundwater flow with their integrated InfoWorks ICM model network. The paper was originally presented at CIWEM’s ‘Surface … Continue reading

Posted in InfoWorks CS, InfoWorks ICM | Tagged , | Comments Off on The Next Frontier: Representing Groundwater Interactions in InfoWorks ICM – User Case Study

ArcGIS and ArcEngine 10.3 are now supported by InfoWorks and InfoNet

For customers who use ESRI ArcGIS or ArcEngine version 10.3, these products are now supported by InfoWorks and InfoNet. In order to use ArcGIS or ArcEngine 10.3 you will need to download the latest patch from our website. The patches … Continue reading

Posted in ICMLive, InfoNet, InfoWorks CS, InfoWorks ICM, InfoWorks RS, InfoWorks SD, InfoWorks WS, IWLive | Comments Off on ArcGIS and ArcEngine 10.3 are now supported by InfoWorks and InfoNet